Table of Contents
High Power Output and High-Capacity Li-Ion Battery
This device features a built-in CTCSS/DCS with programmable channels.
UOX Transmission:
Tx: 420-450 MHz
Rx: 400-520 MHz
| Troubles Solution | |
| No Power. | The battery may be exhausted. Replace or recharge it. Ensure that the battery is installed correctly; if not, remove and reinstall it. |
| The operating time becomes short, even when the battery is fully charged. | Replace the battery. |
| Unable to communicate with transceivers of the same group. | Confirm if the CTCSS/DCS settings are the same. Check if the distance is out of range. |
| The voice of another group can be heard. | Change all QT/DQT settings of the group. |
Unpack and Check Equipment
Carefully unpack the portable radio. We suggest that you check the following items before discarding the packing materials:
- Standard supplied accessories
| Antenna | 1 |
| Battery Charger Kit | 1 |
| Li-ion Battery Pack | 1 |
| Belt Clip | 1 |
| Screws | 1 |
| Hand Strap | 1 |
| User Manual | 1 |
FAMILIAR WITH THIS MACHINE
PTT (Push-to-Talk) Switch
Press the PTT switch, then speak into the microphone to make a call; the indicator lights up red. Release the PTT switch to receive signals; the indicator lights up green.
- Side Key 1: Programmable
- Side Key 2: Programmable
Speaker/Microphone Jack
This is a jack for a speaker microphone or programming cable.
PTT (Push-to-Talk) Switch
The radio’s Side Key 1 and Side Key 2 can be programmed for various functions, using either short press or long press actions. Available functions include:
- Closed
- Monitor
- High/Low Power
- VOX On/Off
Preparation
Lithium-ion Battery Charging Instructions
Plug the power adapter into an AC outlet, turning the charger indicator green. Insert the battery pack ensuring good contact. The indicator turns red during charging, orange at 90%, and green when fully charged. Remove the battery after 9 hours of charging.
Note: Charge only between 5-40°C. Turn off the walkie-talkie before charging, as using it during charging hinders proper operation. If usage time doesn’t increase after charging correctly, replace the battery. Recharging a fully charged battery or leaving it in the charger for over 5 days can damage it.
Function
- Monitor: Adjust the speaker volume with the volume knob.
- High/Low Power: Toggle between high and low power modes.
- VOX ON/OFF: Activate or deactivate the VOX functionality.
- Busy Channel Lockout: Prevent disturbances by disabling transmission if a channel is busy, can be enabled or disabled via PC software.
- VOX Sensitivity: Speak to transmit without pressing the PTT button, sensitivity levels from 0-9 can be set.
- Squelch Level: Adjust the signal strength required to open the receiver with levels from 0-9.
- Voice Guide: Voice guidance available when powered on or during channel selection, options include OFF, Chinese, and English.
- Time Out Timer: Stops transmission after 300 seconds to prevent channel hogging, adjustable timer settings available.
- CTCSS/DCS: Subtone settings allow you to filter signals on the same channel based on matching tones.
- Wide/Narrow Band: Choice to select between wide (25kHz) and narrow (12.5kHz) bands via PC software.
- Battery Save: Reduces power usage when idle, automatically turning off when a signal is received or activity is detected.
- SCAN: Scans active channels and stops as per the scanning mode set, either Carrier or Time Scan.
- Lower Power Alert: Notifies you when the battery is low.
- Voice Compand: Minimizes interference, toggled on/off via PC software.
- ANI Code: Sends DTMF codes in various modes during PTT operations, configured by PC software.
- Programming Password: A password can be set for reading and writing frequency settings to prevent unauthorized changes.