Table of Contents
Exway Flex Paragon Manual
Charging Port
Please charge the Flex Paragon using only the original charger. Once the skateboard is fully charged, the charger’s indicator light will turn green. Ensure the cover is closed after charging to maintain its waterproof performance.
External Discharge
Short press once to display the battery level. Long press for 3 seconds to turn the USB-C external discharge function on or off, with a maximum output of 60W.
Power Button
The power button is located on the ESC at the back of the skateboard. By default, a skateboard in standby mode will automatically turn off after 24 hours. This setting can be modified as needed.
Skateboard indicator light operations and status:
Battery replacement
Lift the battery connector and push the battery in. Connect the power connector and make sure both locks are well fasten.
Remote control
Charging parameters : 5V = 1A
User interface
Operation Guides
Gear button/direction button operation instructions
*Menu callout, tank mode (4WD), parking function only take effect when speed is less than 5km/h, but better set them when the skateboard is totally stationary.
*CRUISE Control: After this function is turned on, if the speed of the board changes greater than 5km/h or the throttle wheel is operated, cruise control will deactivate.
*Shift Lock: This function is turned off by default and gear can be shifted only when the skateboard is stationary.This function can be unlocked from the setting menu.
Once it’ s turned on, the gear can be switched as long the remote roller is centered when the skateboard is rolling.
Touch screen instructions
Speed mode/power mode switching
Double-tap the center of the screen, you can switch speed mode/power mode.
Enter the setting interface
Introduction to setting interface
ATIP:When ATIP function is turned on, the gear N will be entered when the countdown is ended.
2WD/4WD switching, it can be switched successfully only when the board selected is workable with 4WD.
Screen rotation currently supports two directions. (After unlocking the screen lock, keep the screen vertical to the ground for 1 second to switch the direction.)
Lighting Parameter Settings
Swipe right from the left edge/swipe left from the right edge to enter the settings interface.
Click the return button to exit the setting.
Introduction to setting interface
Note: For details, please refer to Exway Rexus remote control operating instructions.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Safety Instructions & Disclaimer
- Using an electric skateboard carries the same potential risks as other sports and may cause injury or even death.
- You must read the instruction manual before use and wear protective gear.
- The belt will wear out under normal use. Please refer to Exway’s related tutorial videos for the correct replacement of a damaged belt.
- Please follow local traffic laws and regulations and use the skateboard safely within the permitted scope.
- It is prohibited for children under 14 years old, disabled people, pregnant women, the elderly, and those with mental disorders or diseases that impair normal body movement, to use the skateboard.
- The skateboard, remote control, and app will be continuously updated, and there may be differences between the manual and the final version of the firmware. For details, please refer to the official website for the latest version.
- If not used for a long time, please charge and discharge the skateboard every 30 days to maintain around 30-75% battery level for storage to ensure battery life.
- After replacing the battery, please ensure that the plug and fixing buckle are properly installed; otherwise, it may affect the power supply and waterproof properties.
- The product has certain waterproof performance, but failure caused by water ingress is not covered by the warranty. Please ensure water resistance.
- Please cover the rubber plug after using the external discharge function to ensure waterproof performance.
FCC Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.